1050 pure aluminum plate sheet belongs to a series of products, according to the international brand naming principles, content must reach 99.5% to the top for qualified products, because they do not contain other elements of technology, the production process is relatively simple, 1050 aluminum plate sheet prices are relatively cheap, is most commonly used in the conventional industry a series of.
High content aluminum alloys such as 1050 Aluminium Plate is sometimes referred to as EC (electrically conduction) at times. Aluminium 1050 Plate contains a minimum of 99.5% and are more electrically conductive than other 1000 series aluminum. Aluminium Plate 1050 are preferred aluminum alloys in the transformer and switch gear markets, as they offer the most economical conductive alloy in the 1000 series.
1050 aluminum H14 sheet/coil is non-heat treatment series is produced in extruded sections. It has excellent cold workability, braze-ability and solder-ability, and it is strengthened by cold working. However, 1050 aluminum sheet/coil has low mechanical strength compared to more significantly alloyed metals. All of these characteristics make 1050 aluminum sheet/coil well suited to chemical and electrolytic brightening but not in casting.
Aluminium Alloy 1050 (1050A) is a popular grade of Aluminium. Alloy 1050 (1050A) is known for its excellent corrosion resistance, high ductility and highly reflective finish. Alloy 1050 (1050A) is typically used for chemical process plant equipment, food industry containers, pyrotechnic powder, architectural flashings, lamp reflectors, cable sheathing.
Elements | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Others | Al | ||
Content | 0.25 | 0.40 | 0.05 | 0.05 | 0.05 | - | 0.07 | 0.05 | 0.15 | Remain |
Alloy Temper | Specified | Tensile strength | Yield strength | Elongation | ||||||||
Thickness(mm) | (MPa) | (MPa) | (%) | |||||||||
1050-O/1050-H111 | 0.2-0.5 | 65-95 | Min20 | Min20 | ||||||||
0.5-1.5 | Min22 | |||||||||||
1.5-3.0 | Min26 | |||||||||||
3.0-6.0 | Min29 | |||||||||||
6.0-12.5 | Min35 | |||||||||||
12.5-80.0 | ||||||||||||
1050-H112 | 6.0-12.5 | Min75 | Min30 | Min20 | ||||||||
12.5-80.0 | Min70 | Min25 | ||||||||||
1050-H12 | 0.2-0.5 | 85-125 | Min65 | Min2 | ||||||||
0.5-1.5 | Min4 | |||||||||||
1.5-3.0 | Min5 | |||||||||||
3.0-6.0 | Min7 | |||||||||||
6.0-12.5 | Min9 | |||||||||||
12.5-40.0 | ||||||||||||
1050-H14 | 0.2-1.5 | 105-145 | Min85 | Min2 | ||||||||
1.5-3.0 | Min4 | |||||||||||
3.0-6.0 | Min5 | |||||||||||
6.0-12.5 | Min6 | |||||||||||
12.5-25 | ||||||||||||
1050-H16 | 0.2-0.5 | 120-160 | Min100 | Min1 | ||||||||
0.5-1.5 | Min2 | |||||||||||
1.5-4.0 | Min3 | |||||||||||
1050-H18 | 0.2-0.5 | Min135 | Min120 | Min1 | ||||||||
0.5-1.5 | Min140 | Min2 | ||||||||||
1.5-3.0 | Min2 | |||||||||||
1050-H19 | 0.2-0.5 | Min155 | Min140 | Min1 | ||||||||
0.5-1.5 | Min150 | Min130 | ||||||||||
1.5-3.0 | ||||||||||||
1050-H22 | 0.2-0.5 | 85-125 | Min55 | Min4 | ||||||||
0.5-1.5 | Min5 | |||||||||||
1.5-3.0 | Min6 | |||||||||||
3.0-6.0 | Min11 | |||||||||||
6.0-12.5 | Min12 | |||||||||||
1050-H24 | 0.2-0.5 | 105-145 | Min75 | Min3 | ||||||||
0.5-1.5 | Min4 | |||||||||||
1.5-3.0 | Min5 | |||||||||||
3.0-6.0 | Min8 | |||||||||||
6.0-12.5 | ||||||||||||
1050-H26 | 0.2-0.5 | 120-160 | Min90 | Min2 | ||||||||
0.5-1.5 | Min3 | |||||||||||
1.5-4.0 | Min4 | |||||||||||
1050-H28 | 0.2-0.5 | Min140 | Min110 | Min2 | ||||||||
0.5-1.5 | ||||||||||||
1.5-3.0 | Min3 |